Difference between revisions of "Layout for DatLab graphs"
From Bioblast
Line 12: | Line 12: | ||
:::: 1 Calibration show temp | :::: 1 Calibration show temp | ||
:::: 2a | :::: ---- | ||
:::: 2b | :::: 2a Slope neg. | ||
:::: 2b Slope neg. (high O2) | |||
:::: ---- | :::: ---- | ||
:::: 3a Flux per volume | :::: 3a Flux per volume | ||
:::: 3b Flux per volume | :::: 3b Flux per volume overlay | ||
:::: 3c Flux per volume | :::: 3c Flux per volume (high O2) | ||
:::: 3d Flux per volume | :::: 3d Flux per volume overlay (high O2) | ||
:::: ---- | :::: ---- | ||
:::: 4a Specific flux | :::: 4a Specific flux | ||
:::: 4b Specific flux | :::: 4b Specific flux overlay | ||
:::: 4c Specific flux | :::: 4c Specific flux (high O2) | ||
:::: 4d Specific flux | :::: 4d Specific flux overlay (high O2) | ||
:::: ---- | :::: ---- | ||
:::: 5a | :::: 5a FCR | ||
:::: 5b | :::: 5b FCR overlay | ||
:::: 5c | :::: 5c FCR (high O2) | ||
:::: 5d | :::: 5d FCR overlay (high O2) | ||
:::: ---- | :::: ---- | ||
:::: Raw signal | :::: Raw signal | ||
Line 36: | Line 37: | ||
::: '''General information''' | ::: '''General information''' | ||
:::: Layouts 1 ff. are considered for O2k-Core applications. | :::: Layouts 1 ff. are considered for O2k-Core applications. | ||
:::: Layouts | :::: Layouts Amp* or pX* are selected for O2k-MultiSensor applications. | ||
::: ''' | ::: '''1 Calibration show temp''' shows O2 concentration and the negative slope in Graph 1 and 2, and temperature and Peltier power in Graph 3: This is the default layout used after switching on the O2k. | ||
:::: Graph 1 & 2: O2 concentration (blue lines, left Y-axis) and O2 slope neg. (uncorrected; red lines, right Y-axis) are displayed, in the top graph for the left chamber (A), and below for the right chamber (B). | :::: Graph 1 & 2: O2 concentration (blue lines, left Y-axis) and O2 slope neg. (uncorrected; red lines, right Y-axis) are displayed, in the top graph for the left chamber (A), and below for the right chamber (B). | ||
:::: Graph 3: The third graph (bottom) shows the block temperature on the left Y axis (red) and the Peltier power on the right Y axis (green). Only when both temperature and Peltier power are constant, the chambers have reached thermal equilibrium. | :::: Graph 3: The third graph (bottom) shows the block temperature on the left Y axis (red) and the Peltier power on the right Y axis (green). Only when both temperature and Peltier power are constant, the chambers have reached thermal equilibrium. |
Revision as of 04:58, 23 May 2016
Description
A Layout in DatLab is a predefined selection of Plots to be displayed at specific Scalings and in a specific order. Any defined graphics Layout can be selected from the Layout menu for defining initial settings for the Plots [Ctrl+F6] and Scaling [F6]. A Layout can be modified and saved under a specific name. In typical standard DatLab graph layouts plots are shown for the left chamber in Graph 1 (top), and for the right chamber in Graph 2 below). During data acquisition, a 30 min time range is frequently used and adjusted to 1 h during the experiment [F6].
Reference: MiPNet19.18C DatLab Guide
MitoPedia O2k and high-resolution respirometry:
DatLab
Layout: O2k-Core
Version: DatLab 7
- 1 Calibration show temp
- ----
- 2a Slope neg.
- 2b Slope neg. (high O2)
- ----
- 3a Flux per volume
- 3b Flux per volume overlay
- 3c Flux per volume (high O2)
- 3d Flux per volume overlay (high O2)
- ----
- 4a Specific flux
- 4b Specific flux overlay
- 4c Specific flux (high O2)
- 4d Specific flux overlay (high O2)
- ----
- 5a FCR
- 5b FCR overlay
- 5c FCR (high O2)
- 5d FCR overlay (high O2)
- ----
- Raw signal
1 Calibration show temp
- General information
- Layouts 1 ff. are considered for O2k-Core applications.
- Layouts Amp* or pX* are selected for O2k-MultiSensor applications.
- General information
- 1 Calibration show temp shows O2 concentration and the negative slope in Graph 1 and 2, and temperature and Peltier power in Graph 3: This is the default layout used after switching on the O2k.
- Graph 1 & 2: O2 concentration (blue lines, left Y-axis) and O2 slope neg. (uncorrected; red lines, right Y-axis) are displayed, in the top graph for the left chamber (A), and below for the right chamber (B).
- Graph 3: The third graph (bottom) shows the block temperature on the left Y axis (red) and the Peltier power on the right Y axis (green). Only when both temperature and Peltier power are constant, the chambers have reached thermal equilibrium.
- During this phase a stirrer test can be performed [F9].
- The next step is to observe equilibration of the oxygen signal with a defined gas phase above the stirred aqueous phase ('open') chamber; usually with air as the first step to perform an oxygen sensor calibration.
- 1 Calibration show temp shows O2 concentration and the negative slope in Graph 1 and 2, and temperature and Peltier power in Graph 3: This is the default layout used after switching on the O2k.
- » O2k-Manual: MiPNet19.18A_O2k-Start